loading

EP Waterproofing System 1 litre

RM 62.00

Please select option below

X

Delivery From Cheras / Selangor
Estimated Arrival : 1-3 working days.
Shipping Fee
RM 13 by courier to Peninsular Malaysia
RM 37 by courier to Sabah, Labuan
RM 37 by courier to Sarawak
Ship To : Within Malaysia
Notify me when it is available again
Add to wishlist
Product ID : 216950484 Brand : EP Model / SKU : Waterproofing System Conditions : New


EP Waterproofing System 1 litre

EP Waterproofing System 1 litre


EP Waterproofing System 1 litre


EP Waterproofing System 1 litre


EP Waterproofing System 1 litre

EP™ Waterproofing System permanently waterproofs and preserves concrete, brick, block and all masonry surfaces & structures in one easy application.

 

EP™ Waterproofing System is manufactured using liquid polymers, creating a liquid nano-waterproofing material.

 

EP™ Waterproofing System is an excellent waterproofing product for all jobs because it cures, hardens, protects and waterproofs in one application.

 

EP™ Waterproofing System is non- toxic, non-flammable and non-caustic.

 

EP™ Waterproofing System doesn’t need to be mixed; it’s easy to use and has no solvents inside* so no bad smells and everything can be washed clean with water.

 

Theoretical Coverage: One (1) litre covers between 4 - 6 square metres.

 

Application Method: Brush, broom or low pressure spray unit (backpack type)

 

* Rain water is harvested from our neighbor’s roof for manufacturing EP™ Waterproofing products.

 

 

APPLICATION INSTRUCTIONS

1. Apply EP™ Waterproofing System to any dry concrete or masonry surface. Test in a small area before any application.

2. Use a low-pressure sprayer - back-pack type - or brush roll on.

3. Treat entire surface area using approximately 1 litre per 3– 6 square metres (32 – 64 square foot). On site product coverage can change depending on the material being treated. 4 square metres per one litre is about the average.

 

EP™ Waterproofing System is best applied by spray method; this is not only fast and effective but will give you an average application rate.

 

EPWPS will surface dry within 1 hour and be traffic ready in 5 hours. For water pond testing – wait 36 hours for standard wet areas. For commercial R.C watertanks they will need a full curing time of 5 days before filling with water for pond/water-tight testing.

 

Allow to dry completely prior to the application of paints or coating.

 

E P™ Waterproofing System will not harm glass, tile or aluminium.

 

 Penetrates into concrete – EPWPS it NOT a surface coating

 Cannot be damaged, torn or broken – unlike membranes or surface coatings.

 Completely waterproofs all masonry in one application (except aerated blocks of course)

 EPWPS be painted over with any coating or material i.e. floor coverings, paints, epoxy, P.U membranes

 Leaves no shine, no gloss and is completely transparent which makes it excellent for facades like face brick, natural stone and most masonry

 EPWPS is not a silane/siloxane sealer. No liquid glass

 EPWPS will stop efflorescence by stopping water penetration

 One product is for all commercial waterproofing – below ground, roof slabs, water tanks, swimming pools, wet areas and car parks

 EPWPS can be used for repair of leaking bathrooms and wet areas without the need for hacking of the tiles

 EP™ Waterproofing System fills the void within the cement and the various aggregates and pores, creating a polymer layer inside the concrete – waterproofing to the core.

 

Contact EP™ for detailed International standards on this product.


Last Updated @ 3/3/2020 10:34:58 AM

 

Last Updated @ 26/9/2023 9:40:19 AM




Average Product Rating

0.0 stars out of 5
5 star
0
4 star
0
3 star
0
2 star
0
1 star
0
Share your thoughts with others
Write a review
Only buyers who purchased the product may leave a review



Information
Copyright © 2024. All rights reserved | www.ecomtb.com.my | Powered by Webstorepro.my
ECOBUILD HARDWARE - TAN MERE LEE 001871965-H